Latest firmware sagemcom f st 2804 v7. How to properly reflash a set-top box from Rostelecom. Automatic router firmware update

The capabilities of standard firmware sometimes do not satisfy the user's requirements, so it becomes necessary to update the router software. The firmware of the Rostelecom router occurs both with an update of the installed program, and with a change to a new one software. The Rostelecom router is updated in several cases: in case of unstable operation, device errors or periodic loss of communication.

Reflashing a router is unsafe, especially for inexperienced users. An incorrectly selected version or a sudden power outage can damage the router.

It is possible to flash the modem automatically or using a computer. When flashing a router from Rostelecom, you should follow all steps sequentially.

Automatic

Some devices are equipped with an automatic software update system. It is important that you have an Internet connection. To automatically flash the device you must:

The installation will start automatically.

Flashing via computer

Firmware algorithm for Rostelecom router via computer:


After this, the update will begin. Upon completion, the Rostelecom set-top box will reboot.

Important! When flashing the firmware, the device cannot be disconnected from the network.

Firmware download links

For different types Rostelecom routers have their own program. You can find out the model at the bottom or side of the device sticker.
It is recommended to download the firmware from the following links:

  • For D-Link, the firmware is obtained from the website ftp://ftp.dlink.ru/.
  • For ASUS, go to the official website in the “Support” section http://www.asus.com/ru/support/, write the name of the device in the search bar,
    go to the “Drivers and Utilities” section, download the appropriate program and update the router.
  • TP-Link: you need to go to the website https://www.tp-link.com/ru/, write the name of the modem and in the “Support” item find the necessary flashing and install it.
  • Zyxel: on the website https://www.zyxel.com/ru/ru/ you select a device, in the “Files and Downloads” section in the “Firmware” block the document is downloaded.
  • Sagemcom: in the list of devices on the website http://sagemcom.ru/catalog_15.htm, select a model and download its program.
  • Linksys: similarly, on the website http://www.linksys.com/ua/support/ you need to select a modem, click on the Download Software link and download the software.
  • ZTE: http://zte.ru/enterprise/products/routers/.

How to reconfigure a Rostelecom router to another provider

When changing your provider from Rostelecom to another, it is important to reconfigure the modem. Algorithm for connecting to the provider:

  1. Reset old settings.
  2. Login to “Device Management”.
  3. Entering new parameters.

To reset the settings, the model has a Reset button. It must be pressed and held for 10 seconds, after which the Rostelecom modem must be connected using wires.
To establish a new connection, you must enter your login and password, connection type and basic information.

To configure the router to work with a new provider, you need to go to “System Data”, where you enter your login and password.
You may need firmware from Rostelecom for your device. Internet settings and Wi-Fi connection data (username and password) are also required to change.

About the backup

To restore settings, there is a chance to create a backup copy. Backup is one of the most reliable ways to save entered data. The algorithm is similar for different models, only the names of the buttons may differ. The format of the downloaded files also differs: for TP-Link the document will be in binary BIN code, for other models it will be in text JSON.

Saving the settings of the Rostelecom router is done as follows:


The recorded data will remain in the computer's memory, and you can always return to it. To restore the settings, click the “Restore” button and specify the path to the address with the settings file.
After this, you need to reboot the Rostelecom router.

Conclusion

Updating the firmware of a router from Rostelecom is an action that requires attention and accuracy. An incorrectly selected version of the router or power surges during installation can damage the device and cause it to fail. By following each step of the router flashing algorithm, you can configure the device yourself without calling a technician.

Increase

Download: Automatic configuration and firmware update/recovery program

Download: Product technical presentation

Specifically designed for the retail and SOHO markets, the F@st2804, v7 router provides
broadband access to the Internet via a high-speed connection. Purchasing a router
F@st2804, v7 the user receives the following benefits:

. High-speed connection via telephone cable, while the phone remains free
. Transferring high-definition IPTV content to digital set-top box
. Providing access and managing multimedia content

BRANDING AND CONFIGURATION UNDER THE LEADING RUSSIAN OPERATOR OJSC ROSTELECOM
The F@st2804, v7 router is branded and fully optimized for the network of the leading Russian operator OJSC Rostelecom. The auto-configuration wizard included in the package contains network configurations for all regions and branches of the operator, and all you need to do to configure the router is select your region during installation.

HIGH SPEED CONNECTION
The F@st2804, v7 router has a modern powerful central processor that
allows you to access the Internet at maximum speed, and also makes
It is possible to view several high-definition IPTV channels simultaneously.

MODERN WIRELESS INTERFACE
The F@st2804, v7 router is compatible with the 802.11b/g/n WFA specification and has the configuration
transmitting and receiving part “2x2” - this allows you to obtain connection speeds of up to
300 Mbit/sec. The router supports modern security protocols: WEP, WPA, WPA2,
filtering by MAC addresses. In addition to this, the router has an automatic
radio channel selection and a separate button with indicator providing maximum
simplicity and convenience of connecting wireless devices using the WPS protocol. Also a router
has an additional button on the body for convenient activation of the wireless interface.

ACCESS TO MULTIMEDIA CONTENT
To provide access to multimedia content through any device and at any time
time, router F@st2804, v7 can work as a DLNA server version 1.5,
supporting Samba, Webdav and UPnP protocols for transmitting multimedia content
(photo, video, music) by local network. The presence of two USB 2.0 Host connectors allows
provide public access to an external USB drive, as well as a USB printer.

FULL IP ROUTER
F@st2804, v7 supports most modern IP services applicable to double-play
to routers:
. IPv6
. Full speed IP routing
. RIP V2/V3, IGMP proxy/snooping
. DHCP server/relay/client
. DNS server/relay, Dynamic DNS

REMOTE CONTROL
The built-in client TR-069 allows the Operator to exercise full control and
setting up the router on the user's side remotely. Also for this task there may be
Standard means were also used: HTTP, FTP upgrade.

NAT and FIREWALL
F@st2804, v7 contains a firewall with the following functions:
. Stateful Packet Inspection
. Complete address/port/protocol filtering
It is possible to configure the passage of traffic through the firewall and NAT for the following
applications:
. VPN: PPTP or IPSec
. VoIP services based on SIP and H.323
. Most popular WEB applications

EASY INSTALLATION AND CONFIGURATION
The CD included with the F@st2804, v7 router contains an automatic
settings, which configures the router in a fully automatic mode.
The visual interface of the wizard is so simple and clear that anyone can use it
even a child. The wizard also contains a diagnostic function that allows you to quickly
solve problems that arise, and, if necessary, provide the necessary
information for the Operator's technical support service.

ALWAYS CONNECTED
Using an external 3G USB modem, the F@st2804, v7 router is able to provide uninterrupted access to the Internet.
When the main channel (ADSL or WAN ETH) becomes unavailable, the router automatically switches to the backup 3G channel.

The router is transferred from in English like a router. A device with its own operating system is used to connect users to the Internet.

Firmware updating of a Rostelecom router, like models from other manufacturers, is performed when it is necessary to improve its capabilities and performance. The new operating system is installed in the router's persistent storage device.

Updating programs in Qtech Rostelecom and other brands of routers does not require resetting the settings, and you can do without a backup copy. But there are different situations, and it’s better to create and save it. To do this you need:

  • go to the “Settings” of the router;
  • open the “System Tools” folder, select the “Backup and Restore” section;
  • select the “Backup” button.

The backup copy is saved in the "Downloads" folder with a bin extension. It is important to have a backup copy of your ADSL modem settings. It may be needed to configure the device after flashing.

Firmware update

Updating the router firmware is an update to the operating system. It is similar to a computer program, but only works with a wired or wireless (Wi-Fi) network. Popular firmware: Linus, Windows 10 ZyXEL and others. There are alternative firmwares.

Router manufacturers, increasing the stability of their devices, release free operating system updates. You can download the updated firmware file from the manufacturer's website. For example, the updated firmware of the Sagemcom 1744 v4 router replaced the earlier versions of Sagemcom 1744 v2 and v2 2. All 3 versions are configured almost identically. The process of installing the firmware is a little complicated, but for beginners there is a special guide called the “Quick Setup Wizard”.

Automatic router firmware update

For routers used by Rostelecom, there is a common set of parameters for all. These include:

  • login and password “admin”, in some models this may be “1234” or an empty string;
  • connection type PPPoE;
  • login/password pair from Rostelecom;
  • VPI and VCI.

Some devices have a built-in automatic firmware update system. You need to go to the web configurator and find the lines “Basic version” and “Updates”. If there are updates, click the “Available” sub-item. On the page that opens with a list of components of the base system, click the “Update” button. The router flashing started automatically.

The device's operating system automatically updates and reboots. At the end of the process, the settings are checked and the provider’s cable is connected to the WAN connector.

How to reflash a modem or router via a computer

Updated firmware for Rostelecom routers is downloaded from manufacturers’ websites using the link posted there. The IP address 192.168.1.2 or 192.168.0.2 is registered on the computer. In the web interface you need to find the “Advanced settings” section. It may be called "System" or "Administration".

Select the “Firmware Update” tab from the menu. In the list of buttons that appears, click “Browse”, select the “Firmware” file and click the “Submit” button. The device flashing starts. When the process is complete, the browser will display the interface again. For GPON ONT terminals there is no need to change the firmware when switching to EPON technology

How to reconfigure a Rostelecom router to another provider

You can reflash the Rostelecom router for another provider yourself. The process consists of the following stages:

  • resetting the settings of the previous provider;
  • finding out information for connecting to the Internet from a new provider;
  • Configuring the device using new parameters.

To reset the contents of a file that is not supported by the new provider, you need to go to the router and click the Reset or “Reset” button. It can be found on the back panel. You need to press for at least 15 seconds. We reset the settings and the router will automatically reboot.

The new provider receives the following data:

  • connection type: for dynamic IP, information about the parameters is not needed; for statistical IP, PPPoE, PPTP or L2TP, you need to know the IP itself, server address, login, password (this data is in the Internet connection agreement);
  • presence of binding by MAC address;
  • MTU value.

Setting up the router begins by connecting the cable from the new provider. It is inserted into the WAN connector. The Administration page opens. You need to add data from the contract with the new provider to the appropriate boxes. Next, the Internet network is configured in the WAN tab. Set wireless connection parameters. To do this, set the WiFi password and the value of the standard user.

When changing residence, or concluding an agreement with an operator, the subscriber will need to set up an Internet connection. If a person does not want to change equipment, he should know how to connect a Rostelecom router to another provider. This is quite easy to do, since all modems and routers work on the same principle.

Algorithm for connecting a modem to a third-party operator:

  1. Reset previous settings.
  2. Login to device management.
  3. Entering new data.

Depending on the router model, some items may differ slightly.

Resetting the parameters that were entered into the router system is very simple. On any model there is a special “reset” button for this. To prevent the user from accidentally pressing it and resetting the system to factory default, the developers hid the button in a special recess. You can press it with any thin stick, for example, an ordinary paper clip. To reset, you must press and hold for 10 seconds.

The fact that the Rostelecom modem is ready to establish a new connection, and the system has been updated, will be notified by a sound signal or the simultaneous lighting of all lights.

After which you can connect the Rostelecom device to another network using wires.

In order to start installing a new Internet, the user needs to find out the details of the third-party provider:

  • login information (login, password);
  • connection type (PPPoE, L2TP, dynamic);
  • connection basics: whether binding is carried out via MAC, IP address (if necessary).

Logging in and setting up a router for another provider

To configure a Rostelecom modem to work with another operator, you need to go to its system data. Depending on the type of connection, you may be required to enter a login and password. Instructions for entering information into the modem parameters can be found on the website of the connected provider.

If the router does not allow you to change data for a third-party operator, the user will have to reflash it. Free latest versions, which are always available on the device manufacturer’s website:

  • ZTE - http://zte.ru/enterprise/products/routers/;
  • TP-LINK – https://www.tp-link.com/ru/products/list-4691.html;
  • Sagem - http://sagemcom.ru/catalog_3.htm;
  • D-Link - http://www.dlink.ru/ru/products/5/.

For correct operation you will need to change:

  • Internet settings;
  • Wi-Fi connection (name, password).

Thus, if necessary, each subscriber can configure the Rostelecom router for another operator by resetting it and setting new parameters.

The Sagemcom Fast 2804 v7 router is designed to connect to the Internet using ADSL (thin telephone cable) or Ethernet (eight- or four-wire twisted pair).

You can also use it to create a home wireless network and connect an IPTV set-top box from Rostelecom.

This article describes the process of setting up the Sagemcom Fast 2804 router for correct operation in the Rostelecom provider network.

Connection

Before starting setup, users will need to properly connect the purchased router. Using the patch cord included in the kit, connect the network card port of your computer or laptop to one of the yellow LAN ports 2-4.

If the Internet comes to you via a telephone line, connect the cable to the connector labeled “ADSL”. If you are provided with a more modern Ethernet connection, plug the supplied cable into the LAN1 port.

Now you can connect the Sagemcom Fast 2804 to power, turn it on and start setting up.

Firmware update and automatic configuration

If you purchased a router from a Rostelecom store, it will come with a special DVD designed to automatically configure the device.

Also, using the disk, users need to update the Sagemcom Fast 2804 firmware version from v5 to v7. The v7 system was developed by Rostelecom specialists and adapted for the most stable connection with the provider’s servers.

Insert the disc into your computer's DVD drive. After this, the Rostelecom Setup Wizard will be automatically launched. You can set all the necessary parameters using the Wizard - in this case, select “Full setup”. Then just follow the program’s instructions; you don’t need to connect to the router’s web interface.

If you prefer to do everything yourself, select “Update”. Wait a moment until firmware v7 is installed on the Sagemcom Fast 2804, then close the program and proceed to the next step in the guide.

Authorization in the Web interface

  • Launch any internet browser.
    In the addressing line, you must enter the device address, which is indicated on the sticker on the bottom cover of the router. If there is no sticker on the case, you need to go to properties local connection and look at the value of the “Default gateway” parameter.
  • A pop-up window will open in which users need to provide a login and password to access the router management menu. This information is also indicated on the sticker. You can try the most commonly used combination: "admin" and "admin".

  • If you did everything correctly, the interface for controlling the operation of Sagemcom Fast 2804 v7 will open.

Setting up a network connection

  • Using the navigation menu on the left side of the window, go to the “Advanced” tab.
  • Open the “WAN service” section and delete all existing connections. To do this, mark them and click “Delete”.
  • In a similar way, delete all the contents of the “Second Level Interface” section.
  • Click on the “Add” button.
  • Rostelecom subscribers must indicate the values ​​of the VCI and VPI parameters, which depend on the region of residence. You can clarify the correct parameters by contacting technical support by phone (a list of numbers is available).

  • Click Apply and Save.
  • Go to the “WAN Service” tab and click “Add”.
  • Select the connection you just created from the drop-down list and proceed further.
  • In this step, users need to specify the connection type. In most cases, you will receive Internet from Rostelecom via a PPPoE connection.

  • Enter your username and PPP connection key, which are specified in the service agreement with Rostelecom (all information is available). You can specify any service name, it does not affect anything.

  • Check the box next to “Retry PPP on error”.
  • You can skip the remaining steps. Click "Apply and Save" to complete the settings.

Setting up a router to work with a TV set-top box

If you want to connect a set-top box via the Sagemcom Fast 2804 v7 router, you must do the following:

  • In the “Second Layer Interface” tab, create another connection (the VCI and VPI values ​​for IPTV will be different).
  • In the “WAN service” section, create a new object and select the created connection.
  • Select the service type "Bridge" and click "Apply".

  • Open the “LAN” tab.
  • Check the box next to “Disable DHCP server”.
  • Enable the IGMP Snooping and IGMP Proxy on Bridge options.

WiFi Configurations

  • Expand the “WLAN” category and go to the “Basic” section.
  • Activate the “Enable wireless network” and “Enable multicast transmission” items.
  • Enter the access point name in the SSID field.
  • Go to the "Security" category.
  • Select authentication using "WPA-PSK", encryption using "TKIP and AES".

  • Enter your access key (at least 8 characters).
  • Click "Save".

This completes the router setup. In the “Management” section, find the “Reboot” tab and restart your modem to activate all the changes made.